New Proxmox VM with Home Assistant

Support Promox 7

• remove susbcription and add non-susbcription
• add zip support

Telegram channel

• https://t.me/proxmoxha

forked from whiskerz007/proxmox_hassos_install This script will create a new Proxmox VM with the latest version of Home Assistant. To create a new VM, run the following in a SSH session or the console from Proxmox interface

bash -c "$(wget -qLO - https://raw.githubusercontent.com/patriciocl/proxmox_hassos_install/master/install.sh)"

After script completes, click on the new VM (the script will tell you the ID), click on the Hardware tab for the VM and change the Memory and Processors settings to what you desire. The Hard Disk can be expanded by clicking on it, then click on the Resize disk button above (Note: additional steps must be taken for storage to take effect in the VM after the first boot). The network MAC address can be changed by selecting Network Device and clicking Edit above. Once all changes have been made, click Start above.

Root Prompt

To get to the root prompt

• Open the console after the VM has been started
• When the messages slow down press the Enter key a couple of times until you see the following

Welcome to Home Assistant
homeassistant login:

• Login using root, no password is requested
• When you see the hassio > prompt, type login
• You should now see a # prompt.

Add a serial port

By adding a serial port, you are able to use a different interface to interact with the VM. When you click on the down arrow next to Console you will be able to use xterm.js which enables you to Right-Click and get access to Copy and Paste functions. If the serial port was already added by the install script, no further actions are required to enable the functionality.

• Click on the VM in the list of containers at the left side panel
• Click Hardware tab located beside the list of containers
• Click Add located beside Summary tab, then click Serial Port
• Serial Port should be set to 0 in the input box, then click Add
• Start the VM, if it isn't already
• At the root prompt type sed -i 's/$/ console=ttyS0/' /mnt/boot/cmdline.txt
• A Shutdown and Start is required for the changes to take effect

Show Current IP Address

To get the current IP address assigned to the VM from the Proxmox interface

• Click on the VM in the list of containers at the left side panel
• Click Summary tab located beside the list of containers
• Click More near IPs in the top left section
• You can find the assigned IP addresses on the line with the name similar to enp0s18

To get the current IP address assigned to the VM from the command line

• At the root prompt type nmcli -g ip4.address d sh $(nmcli -g device c)
• The response will be the IP address with subnet mask or nothing

Note: If DHCP is configured and nothing is shown, check DHCP server and VM network settings

Configure Network for Static IP Address

To set a static IP address, use the following as an example

• At the root prompt type nmcli c mod $(nmcli -g uuid c) ipv4.method manual ipv4.addresses "192.168.20.170/24" ipv4.gateway "192.168.20.1" ipv4.dns "8.8.8.8,8.8.4.4"
• At the root prompt type nmcli c up $(nmcli -g uuid c)

Configure Network for DHCP

To remove all static IP addresses and enable DHCP

• At the root prompt type nmcli c mod $(nmcli -g uuid c) ipv4.method auto ipv4.addresses "" ipv4.gateway "" ipv4.dns ""
• At the root prompt type nmcli c up $(nmcli -g uuid c)

Default Interface Name

To get the default interface name

• At the root prompt type nmcli -g device c
• The response with be the interface name

Change Hostname

To change the HassOS VM hostname

• At the root prompt type hostnamectl set-hostname your-new-hostname
• You can verify the change by logging out with exit, the last line printed will be your-new-hostname login:

Resize Disk

To resize the disk after the first boot

• At the root prompt type df -h /dev/sda8 and note the Size
• Shutdown the VM
• Resize the disk to the desired size
• At the root prompt type sgdisk -e /dev/sda
• At the root prompt type reboot
• Verify resize was successful by typing df -h /dev/sda8 at the root prompt